Bacharach PCA2 Especificações Página 99
- Página / 116
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Instruction 24-9448 6-9
Maintenance
12. Plug the sensor into analyzer; and then reattach tubing to gas cup.
13. Install the sensor retainer and battery cover.
14. Allow the sensor that was just installed time to stabilize in the circuit
before continuing with this procedure. Stabilization time for all sen-
sors (except for the NO sensor) is about 1 hour. The NO sensor baseline
technically requires several days to stabilize but should be sufficiently
stabilized for use in approximately 4 hours.
15. Turn ON the analyzer and confirm that no sensor errors occur during
warm up.
Note: Discard an old sensor in accordance with local and federal haz-
ardous waste disposal laws.
16. Calibrate the new sensor(s) per Section 5 (except the O2 sensor which
does not require calibration).
- Portable Combustion Analyzer 1
- WARRANTY 2
- Contents 3
- Instruction 24-9448 4
- 1 Introduction 7
- Instruction 24-94481-2 8
- Instruction 24-9448 1-3 9
- 1.3 Features & Benefits 10
- 1.4 Operational Overview 11
- 1.5 Connector Descriptions 12
- Figure 1-1. PCA 2 Components 13
- 1.5.3 POWER (AC Adapter) 14
- 1.6 Front Panel Buttons 15
- Instruction 24-94481-10 16
- Introduction 16
- 2 Specifications 17
- Normal Operating Conditions: 18
- Performance: 18
- Instruction 24-9448 2-3 19
- Specications 19
- Instruction 24-94482-4 20
- 3 Initial Setup 21
- 3.1 Scope 21
- 3.2 Power 21
- Instruction 24-94483-2 22
- Initial Setup 22
- T-STACK T-AIR 23
- 3.4 Operating Parameters 24
- 3.5 Fuel Selection 24
- Instruction 24-9448 5 25
- 3.7 Pressure Units Selection 26
- Instruction 24-9448 7 27
- 3.9 Date Setup 28
- 3.10 Time Setup 29
- Reference Setup 30
- Instruction 24-9448 11 31
- O2 4.0 % 32
- CO 12 ppm 32
- EFF 82.6% 32
- Instruction 24-9448 13 33
- 3.15 Logging Selection 34
- 3.16 Button Sound 34
- 3.17 Test ID Information 35
- Instruction 24-944816 36
- 3.18 Username 37
- Instruction 24-944818 38
- 3.19 Language 39
- 3.20 Cal Reminder Period 40
- 3.21 Run/Hold Screen Format 41
- Instruction 24-944822 42
- Instruction 24-9448 23 43
- 4 Operation 44
- 4.1 Operating Tips 44
- --- % 45
- T-STK 71.5 °F 45
- T-AIR 71.5 °F 45
- EA --- % 45
- CO(0) --- ppm 45
- 4.3 Selecting a Fuel 46
- 4.4 Sampling Point 47
- Instruction 24-9448 4-5 48
- Operation 48
- 4.6 Pressure Label Selection 50
- Instruction 24-94484-8 51
- 4.9 Saving Test Data 53
- 4.10 Ending a Combustion Test 54
- 4.11 Emptying the Water Trap 54
- 4.13 Low Battery Alarm 55
- 4.14 Data Logging 56
- Instruction 24-94484-14 57
- Instruction 24-9448 4-15 58
- Instruction 24-94484-16 59
- Where: “xx” is the memory 59
- 4.15 Memory 60
- Instruction 24-94484-18 61
- Instruction 24-9448 4-19 62
- 4.15.3 Clearing Memory 63
- Instruction 24-9448 4-21 64
- Instruction 24-9448 4-23 66
- Instruction 24-94484-24 67
- Select (Advanced) 68
- Name of new USB 68
- Instruction 24-9448 4-25 68
- 4.16.3 Recovering Data 69
- Instruction 24-9448 4-29 72
- Instruction 24-94484-30 73
- 4.18 Printing Test Data 74
- ∗∗∗) appear in the data 75
- Instruction 24-9448 4-33 76
- 5 Calibration 77
- 5.1 Smart Sensors 77
- 5.2 Starting a Calibration 77
- 5.3 Pressure Sensor 78
- Calibration 78
- 5.4 T-Stack Calibration 80
- ENT to calibrate the TS-Zero 81
- ENT to cali 81
- 5.5 T-Air Calibration 82
- Instruction 24-9448 5-7 83
- 5.6 CO-LO Sensor Calibration 84
- ENT to calibrate the H 85
- Sensor Calibration 86
- 5.8 NO Sensor Calibration 87
- ENT to calibrate the NO 89
- ENT to display 89
- 6 Maintenance 91
- 6.1 PCA 2 Disassembly 92
- Type and position 93
- +∆P (Top) 93
- –∆P (Bottom) 93
- PRESSURE 94
- PURGE AIR 94
- Figure 6-4. Wiring 95
- Instruction 24-94486-6 96
- 6.3 Smart Sensor Replacement 97
- 6.4 Sensor Only Replacement 98
- Instruction 24-9448 6-9 99
- Instruction 24-94486-10 100
- Maintenance 100
- 6.6 Thermocouple Replacement 101
- Instruction 24-94486-12 102
- 6.7 Pump Replacement 103
- 6.8 Cleaning the Probe 104
- 7.1 Analyzer Repair 105
- 7.2 Error Symbols 105
- 7 Troubleshooting 105
- Instruction 24-94487-2 106
- Troubleshooting 106
- ENT to display the 107
- ENT to display the DEVICE 108
- 8 Parts & Service 109
- 8.1 Replacement Parts 109
- Figure 8-1. Parts (2 of 2) 111
- 8.2 Accessories 112
- Instruction 24-9448 8-5 113
- Parts & Service 113
- 8.3 Service Centers 114
- Printed in U.S.A 116
Manuais e produtos relacionados com Medição, teste e controlo Bacharach PCA2
(20 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais